Introduction

Often I hear from people that it’d be nice to have U-Boot running on 96Boards at full pace. Even though U-Boot is supported for couple of our 96Boards, we are still lagging behind using the nice to have features of it. One of which is extracting boot environment from uEnv.txt. This blog addresses this pitfall and also explains about how to boot Linux from SD card using the environment from U-Boot’s uEnv.txt.

U-Boot

Das U-Boot (Universal Bootloader) is the the popular Open source bootloader for Embedded devices. It offers wide range of flexibility in terms of booting from different sources and so on. Usually U-Boot will be put up as a secondary or later stage bootloader for the SBC’s. The reason behind that is, in most of the SoC’s there will a ROM bootloader which gets executed first. U-Boot binary is available in two flavours:

1. SPL - MLO
2. U-Boot - u-boot.img

SPL is the stripped version of the full fledged U-Boot binary. It is often used in cases where the memory available for second stage bootloader is scarce or the second stage bootloader has to boot using internal RAM/Flash. In those cases, SPL will initialize some externally connected peripherals like eMMC,SRAM etc.., and then it loads the final U-Boot onto external SRAM.

But for Dragonboard, SPL is not needed as the U-Boot finds its place in third stage of the booting process and by the time ample amount of external RAM and Flash is available for it to use. Below, is the booting process involved in Dragonboard410c for U-Boot:

ROM bootloader---->LK bootloader---->U-Boot---->Linux Kernel

Boot Environment

U-Boot supports two types of boot environment. One is the hard coded environment which is available as a part of the binary and another is the extracted environment from SD card or eMMC. For Dragonboard, internal environment variables are available in include/configs/dragonboard410c.h and external environment would be extracted from uEnv.txt available from SD card’s ext4 partition.

Once the boot environment is extracted from uEnv.txt it will get imported into the environment table of U-Boot. Later those environment variables could be seen by printenv command. It is also possible to pack the commands under one variable and execute it using run command.

For instance, below is the environment variable contains command to load and import env from SD card.

"loadbootenv=if ext4load mmc 1:1 ${scriptaddr} ${bootenv}; then " \
                "echo Loaded environment from ${bootenv}; " \
                "run importbootenv; "\
            "fi;\0" \

The above variable could be executed by the following command:

=>dragonboard410c: run loadbootenv

Booting Linux from SD card

Now, lets get into the detail of booting Linux from SD card using U-Boot. The complete guide containing the instructions is avaialbe in 96Boards Documentation repository.

First, SD card needs to be formatted in such as way that the first partition should be of ext4 type. This is the place, we will store the RFS (Root File System), Kernel image, dtb, uEnv.txt etc… Usually Kenrel image would be placed in FAT partition and RFS would be in ext4 partition. But, we are going to place the Kernel image under RFS itself.

After formatting SD card, download the OpenEmbedded RFS from 96Boards build, extract it and flash onto SD card’s first partition. By the end of this step, the first partition of SD card should have entire Root File System populated.

Now, build the Linux Kernel along with device tree using the instructions available in release notes. Then, convert the generated Kernel image to the format recognized by U-Boot(uImage) using mkimage tool.

$ sudo apt-get install u-boot-tools
$ mkimage -A arm64 -O linux -C none -T kernel -a 0x80080000 -e 0x80080000 -n Dragonboard -d arch/arm64/boot/Image uImage

Note: arch/arm64/boot/Image is inside the kernel directory

Once the image has been created successfully, you should get something similar to following output

Image Name:   Dragonboard
Created:      Sat Jul 29 15:15:27 2017
Image Type:   aarch64 Linux Kernel Image (uncompressed)
Data Size:    17349120 Bytes = 16942.50 kB = 16.55 MB
Load Address: 80080000
Entry Point:  80080000

After getting uImage copy it along with device tree blob apq8016-sbc.dtb to /boot directory in SD card’s ext4 filesystem. Final step is to place the uEnv.txt file containing the environment variable for U-Boot. So, create a file uEnv.txt in /boot driectory of SD and paste the following contents to it.

bootargs=root=/dev/mmcblk1p1 rw rootwait console=tty0 console=ttyMSM0,115200n8 rootfs=ext4 noinitrd selinux=0
bootcmd=ext4load mmc 1:1 ${kernel_addr_r} /boot/uImage; ext4load mmc 1:1 ${fdt_addr_r} /boot/apq8016-sbc.dtb; bootm ${kernel_addr_r} - ${fdt_addr_r}
uenvcmd=run bootcmd

Above environment variables instructs U-Boot to fetch Kernel image and device tree blob from /boot/ directory in SD card’s first partition. It also specifies the boot arguments (bootargs) to be passed by U-Boot to Linux kernel. When U-Boot imports environment from uEnv.txt it scans for the uenvcmd and executes it.

Finally, eject SD card from host and insert it onto Dragonboard410c and boot it. U-Boot will automatically fetch the environment and loads Kernel image and dtb onto RAM, then transferrs control to it. If any of the step fails, appropriate error message will be shown in the U-Boot console.

Note: By default, U-Boot console is available through on board UART in Dragonboard410c.

Conclusion

I hope this blog has provided much information to boot Linux using U-Boot from SD card. More detailed steps are availabe in the Documentation repo.

As we always say, if you encounter any issues or have any suggestion please report it in comments/forum. We are glad to help you :-)