HEre’s the log I have through the UART
clear reset source
last_keypoint32,reboot_type16
secdbg not DCU.
SecDbgVer exit
xloader chipid is: 0x36600110, start at 460ms.
Build Date: Sep 19 2017, 15:34:09
[clock_init] ++
hikey960 [hikey960_clk_init]
hi3660 [clk_setup]
[clock_init] –
storage type is UFS
ufs retry: 6 count v_tx:0 v_rx:0
ufs set v_tx:0 v_rx:0
Hikey960[5301] no need avs_init.
ddr ft:0xf20332a3,mode:1 target:4
UceLdOk
ch 0 gt_errfail, STATUS:0x00000060
ch 0 gdst_errfail, STATUS:0x00000040
ch 1 gt_errfail, STATUS:0x00000060
ch 1 gdst_errfail, STATUS:0x00000040
ch 2 gt_errfail, STATUS:0x00000060
ch 2 gdst_errfail, STATUS:0x00000040
ch 3 gt_errfail, STATUS:0x00000060
ch 3 gdst_errfail, STATUS:0x00000040
timeout
timeout
timeout
timeout
density: 0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000
ddr info 0x00000306
400M
685M
1067M
C2R,V0x0000002c e:66
C0R,V0x0000002c e:66
C1R,V0x0000002c e:66
C2R,V0x0000002d e:66
C3R,V0x0000002d e:66
C0R,V0x0000002d e:66
C1R,V0x0000002d e:66
C2R,V0x0000002e e:66
C3R,V0x0000002e e:66
C0R,V0x0000002e e:66
C1R,V0x0000002e e:66
C2R,V0x0000002f e:65
C3R,V0x0000002f e:66
C0R,V0x0000002f e:65
C1R,V0x0000002f e:65
C2R,V0x00000030 e:65
C3R,V0x00000030 e:65
1244M
1866M
C1R,V0x00000016 e:66
C2R,V0x00000016 e:66
C0R,V0x00000017 e:66
C1R,V0x00000017 e:66
C2R,V0x00000017 e:66
iomcu_subsys_init
boot_c0 PROFILE 4
slave0 irq0:0x00000014
slave1 irq0:0x00000014
main: ******** Fastboot for Kirin *****************
main: ******** Build Date: Jun 2 2017, 17:34:24 **
main: ******** Fastboot start at 1809 ms **********
main: print soc_id computed in xloader phase, is below:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
led_alwayson: can’t get dtb operators
bbox: bbox_register_module_ops success.
bfm: : >>>>>enter bfm_init
bfm: : [disable_boot_fail_system] boot_fail_system state is 0
clock: PLL Stat
clock: PLL2 ctrl0=0x04909604,ctrl1=0x02000000
clock: PLL2 acpu en_stat:0x00000008, acpu gt_stat:0x00040000
clock: PLL2 final en_stat:0x00100000, final gt_stat:0x00020000
clock: PLL3 ctrl0=0x04904005,ctrl1=0x07000000
clock: PLL3 acpu en_stat:0x00000000, acpu gt_stat:0x00000000
clock: PLL3 final en_stat:0x00200000, final gt_stat:0x00040000
clock: clock init OK
ufs: ufs start on platform[36600110]ufs: ufs current mode: 0x00000011
ufs: ufs current gear: 0x00000003
ufs: ufs mphy reg 0x4A = 0x00000000
ufs: bUD0BaseOffset: 0x00000010, bUDConfigPLength: 0x00000010
ufs: UFS device manufacturerid = 0x000001ce
ufs: UFS device: S******
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000001, mntnStageCode is 27
bfm: : <<<<<exit set_boot_stage.
storage: emmc_ops invalid
storage: storage type is UFS
bfm: : bfm system is disabled!
storage: emmc_init: BL2_STAGE_EMMC_OK is 33554435!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000003, mntnStageCode is 29
bfm: : <<<<>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010001, mntnStageCode is 30
bfm: : <<<<<exit set_boot_stage.
ddr: current logic version is lpddr4 verison !!!
ddr: ddr size is 3072MB
bbox: register modid [0x81fff200]
bbox: register exception succeed.
bbox: register modid [0x81fff202]
bbox: register exception succeed.
bbox: register modid [0x81fff20b]
bbox: register exception succeed.
watchdog: Enable watchdog start
boardid: [BDID]boardid: 5301
gpio: hikey960_gpio_init: GPIO 46 202 206 ouput low, GPIO 219 pullup.
load_kernel: register_update_dt_ops for usb!
usb: [USBERR]random_serial: fastboot serial: 0631326473000000
secureboot: Enter secboot_init: set pll efuse flag!
secureboot: pll efuse flag has been succ set!bbox: register modid [0x81fff20a]
bbox: register exception succeed.
secureboot: SECBOOT_DEV_INFO_DADDR = 0x1d7fff00, SECBOOT_DEV_INFO_SIZE = 0x00000040!
dtimage: number of dtb = 1
dtimage: =========uncompress_dtb_addr=[0x16f00000],====vrl_addr=[0x1b0e64e0]====
dtimage: [device_tree_get_dtb_entry:215] Verify Not Exist
dtimage: fdt_init success!
dtimage: -----can not find hisilicon,fastboot node by compatible
dtimage: -----can not find hisilicon,fastboot node by compatible
load_kernel: register_update_dt_ops for led!
dtimage: -----can not find hisilicon,fastboot node by compatible
vibrator: vibrator_delay: hisilicon,fastboot motor-vib_type failed!
dtimage: -----can not find hisilicon,fastboot node by compatible
vibrator: vibrator_off: hisilicon,fastboot motor-vib_type failed!
reboot_reason: scsysstat_value is 0x00000000
pmu: can not find fastboot,hisi-pmic-mntn node1
pmu: pmu_property_read_u32 fastboot,hisi-pmic-mntn, hisilicon,data-width, failed
pmu: pmu_mntn_record_dts_parse failed!
reboot_reason: enter [check_hardware_reset]
reboot_reason: Could not find path /sysctrl_reason
reboot_reason: get_sysctrl_reason_data is error
ddr: reset dmc_rint_0:00001000
ddr: reset dmc_rint_1:00000040
ddr: reset dmc_rint_2:00001040
ddr: reset dmc_rint_3:00000000
ddr: new dmc_rint_0:00000000
ddr: new dmc_rint_1:00000000
ddr: new dmc_rint_2:00000000
ddr: new dmc_rint_3:00000000
bbox: save_tempbuffer_to_loop_area():727:storage_read fail[-1]
reboot_reason: reboot_reason is coldboot
reboot_reason: clear_reset_source in!
reboot_reason: tmp =0x0effcc70
dtimage: -----can not find fastboot,charger node by compatible
power: get_chargerIC_type: getU32byCompatible fastboot,charger, hw_charger_type failed!
dtimage: -----can not find fastboot,coul node by compatible
power: get_coul_type: get coul_type failed!
power: get coul_type failed!
power: hi6421v500 register coulometer ops fail!
dtimage: -----can not find huawei,hisi_bci_battery node by compatible
no_module: [hi6523_get_config_info]: can’t get battery board type
dtimage: -----can not find fastboot,charger node by compatible
no_module: get hi6523 i2c reg num fail!
dtimage: -----can not find fastboot,charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get ichrg_pre_limit fail
dtimage: -----can not find huawei,hi6523_charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get reg fail
dtimage: -----can not find fastboot,buckboost node by compatible
max77813: get_buckboost_type: getU32byCompatible fastboot,buckboost, hw_buckboost_type failed!
max77813: get dts buckboost type fail!
cpu_buck: pmu type3 not registered
cpu_buck: Bad cpu buck info:1
bbox: Could not find path /rdr
bbox: Could not find status property.
mntn: tele_mntn_stat_point_init: can not bbox_ops !
dtimage: -----can not find hisilicon,fastboot node by compatible
mntn: [tele_mntn_m3_wdt_config]: getU32byCompatible(hisilicon,fastboot, lpm3-board-type) error!
mntn: mntn init
mntndump: enable_reserved_ddr_dts: Could not find path /reserved-memory/mntndump
mntndump: mntn_dump_init failed
mntndump: get_mntn_dump_addr:mid[2] is not init
mntn: kernel dump is not available
mntn: reboot_type is 16
mntn:
no need to dump_mem…
mntn: enter [registe_pstore_ramoops_dump]
mntndump: get_mntn_dump_addr:mid[5] is not init
mntn: no mdump_pstore info
mntn: M3_RDR_SYS_CONTEXT_BASE_ADDR is null
uart_cfg: [MNTN]:Could not find node.
uart_cfg: set_default_uart_cfg: uart_from_dts_read failed!
uart_cfg: module_idx 2, uart_no 6
uart_cfg: odule_idx 11, uart_no 15
uart_cfg: module_idx 2, uart_no 6
uart_cfg: getU32byCompatible(hisilicon,fastboot, uart-board-type) error!
uart_cfg: boardid: 5301 use uart port: 6
pasr: in pasr_init-43 …ddr: current logic version is lpddr4 verison !!!
ddr: current logic version is lpddr4 verison !!!
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_detect_type: huawei,lcd_panel_type: get detect_type fail
display: lcd:no lcd detect_type
no_module: [LOGO] get_logo_buffer_from_dtsi: Could not find path /reserved-memory/logo-buffer.
no_module: [LOGO] logo_init: logo init failed!!! used the default fb addr.
display: [display]jdi_nt35696_panel_init: lcd type is not JDI_NT35696_5P5_LCD.
display: [display]jdi_otm2503b_panel_init: lcd type is not JDI_OTM2503B_5P5_LCD.
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010002, mntnStageCode is 31
bfm: : <<<<<exit set_boot_stage.
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_dts_value: can not get huawei,lcd_panel_type, bl_bus_id=4!
dtimage: -----can not find ti,lm36923 node by compatible
display: [display]get_dts_value: can not get ti,lm36923, support=0!
display: get lm36923_support failed!
Audio_codec: [audio]:Could not find “hisilicon,codec-controller” node.
load_teeos: can not find fb node fingerprint
load_teeos: failed to find fb node ese_config
display: [display]hisi_get_disp_info: hisifb_data is NULL pointer, return!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010003, mntnStageCode is 32
bfm: : <<<<<exit set_boot_stage.
misc: [get_misc_message] mmc_read failed
preboot: [fastboot]: check_unlock_misc_info, line:1273 :get misc message failed.
preboot: [fastboot]: check_powerkey_misc_info, line:1242 :!!!CAUTION!!!:get keypad_operator FAIL!
preboot: [fastboot]: check_volumekey_state, line:943 :!!!CAUTION!!!:get keypad_operator FAIL!
misc: [get_misc_message] mmc_read failed
preboot: [fastboot]: comm_read_misc_cmd, line:501 :get misc message failed.
rescue: ^^^^^^^^^[rescue_init] ok !
usbloader: bootmode is 1
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010004, mntnStageCode is 33
bfm: : <<<<<exit set_boot_stage.
load_lpm3: start lpm3 loading
load_lpm3: load lpmcu image
tm: cluster0 prof0 trim result check fail:0,00000000,00000000
tm: cluster0 prof1 trim result check fail:0,00000000,00000000
tm: cluster0 prof2 trim result check fail:0,00000000,00000000
tm: cluster0 prof3 trim result check fail:0,00000000,00000000
tm: cluster0 prof4 trim result check fail:0,00000000,00000000
tm: cluster1 prof0 trim result check fail:0,00000000,00000000
tm: cluster1 prof1 trim result check fail:0,00000000,00000000
tm: cluster1 prof2 trim result check fail:0,00000000,00000000
tm: cluster1 prof3 trim result check fail:0,00000000,00000000
tm: cluster1 prof4 trim result check fail:0,00000000,00000000
tm: cluster1 prof5 trim result check fail:0,00000000,00000000
tm: cluster2 prof0 trim result check fail:0,00000000,00000000
tm: cluster2 prof1 trim result check fail:0,00000000,00000000
tm: cluster2 prof2 trim result check fail:0,00000000,00000000
tm: cluster2 prof3 trim result check fail:0,00000000,00000000
tm: cluster2 prof4 trim result check fail:0,00000000,00000000
tm: cluster2 prof5 trim result check fail:0,00000000,00000000
tm: cluster2 prof6 trim result check fail:0,00000000,00000000
tm: cluster2 prof7 trim result check fail:0,00000000,00000000
tm: C0
tm: p4
tm: path adjust:00000018
tm: svfd2:00000011
tm: svfd1:00000012
tm: svfd0:00000012
tm: p3
tm: svfd2:00000011
tm: svfd1:00000010
tm: svfd0:00000011
tm: C1
tm: p4
tm: path adjust:00000018
tm: svfd2:00000014
tm: svfd1:00000013
tm: svfd0:00000013
tm: p3
tm: svfd2:00000016
tm: svfd1:00000016
tm: svfd0:00000016
tm: p2
tm: svfd2:0000001a
tm: svfd1:0000001a
tm: svfd0:0000001a
tm: p1
tm: svfd2:0000001a
tm: svfd1:0000001a
tm: svfd0:0000001a
load_lpm3: do_lpnv_acpufreq_papa_option
load_lpm3: modify_pmu6422_para no bugfix
load_lpm3: LPM3 load success 0x89c80000
load_lpm3: SCPERRSTSTAT4_SEC fffffffc
load_lpm3: SCOCBCRSTCTRL 00000000
load_lpm3: SCPERCLKEN2 43e00001
load_lpm3: SCPERSTAT2 c7fa4c4f
load_lpm3: SCOCBCSTAT 00007250
load_lpm3: AOCLK_CTRL 00000725
load_lpm3: SCPERSTAT3 000014c7
load_lpm3: SCOCBCSTAT 00007250
load_lpm3: AOCLK_CTRL 00000725
load_lpm3: AOCLK_CTRL 00000225
load_lpm3: CFG_M3_RST_STA 00000000
load_lpm3: load ocbc success!
load_kernel: 0xC5 = 00000032
load_kernel: 0xCC = 00000003
bfm: : bfm system is disabled!
load_kernel: load_kernel CONFIG_WITHOUT_SECURE_OS is open
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010005, mntnStageCode is 34
bfm: : <<<<<exit set_boot_stage.
load_kernel: INVALID BOOT IMAGE HEADER
bfm: : bfm_to_mntn_modid: size is 8
bfm: : >>>>>enter boot_fail_err
bfm: : boot_fail_err: bootErrNo is 0x02010006, mntnModID is 0x81fff209, mntnRBReason is 0x0000007d, e.e_reboot_priority is 1, g_sug_recovery_mtd is 0
bbox: register modid [0x81fff209]
bbox: register exception succeed.
bbox: record exce_type is 0x0000007d
bbox: -------show exception info begin
bbox: modid: [0x81fff209]
bbox: reboot_pri: [0x00000001]
bbox: dump_mod_mask: [0x0000000000000003]
bbox: reset_mod_mask: [0x0000000000000003]
bbox: from_module: [0x0000000000000001]
bbox: reentrant: [0x0f00da01]
bbox: exce_type: [0x0000007d]
bbox: reserve_u64: [0x0000000000000000]
bbox: reserve_p: [0x00000000]
bbox: -------show exception info end
bbox: dump module [0000000000000001] start!
bbox: modid is 0x81fff209, etype is 0x0000007d, mod_group_id is 0x0000000000000001
bbox: modid:[0x81fff209], coreid:[0x0000000000000001]
bbox: bbox_dump_done current mask:[0x0000000000000001]
bbox: dump module [0000000000000001] end!
bbox: Skip module [0x0000000000000001]
bbox: bbox_notify_module_hikey960 boarid:5301 xloader use UART6
scsysstat_value[8].
clear reset source
last_keypoint34,reboot_type125
secdbg not DCU.
SecDbgVer exit
xloader chipid is: 0x36600110, start at 452ms.
Build Date: Sep 19 2017, 15:34:09
[clock_init] ++
hikey960 [hikey960_clk_init]
hi3660 [clk_setup]
[clock_init] –
storage type is UFS
ufs retry: 6 count v_tx:0 v_rx:0
ufs set v_tx:0 v_rx:0
Hikey960[5301] no need avs_init.
ddr ft:0xf20332a3,mode:1 target:4
UceLdOk
ch 0 gt_errfail, STATUS:0x00000060
ch 0 gdst_errfail, STATUS:0x00000040
ch 1 gt_errfail, STATUS:0x00000060
ch 1 gdst_errfail, STATUS:0x00000040
ch 2 gt_errfail, STATUS:0x00000060
ch 2 gdst_errfail, STATUS:0x00000040
ch 3 gt_errfail, STATUS:0x00000060
ch 3 gdst_errfail, STATUS:0x00000040
timeout
timeout
timeout
timeout
density: 0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000
ddr info 0x00000306
400M
685M
1067M
C2R,V0x0000002c e:66
C3R,V0x0000002c e:193
C1R,V0x0000002c e:66
C2R,V0x0000002d e:66
C3R,V0x0000002d e:66
C0R,V0x0000002c e:66
C1R,V0x0000002d e:66
C2R,V0x0000002e e:66
C3R,V0x0000002e e:66
C0R,V0x0000002d e:66
C1R,V0x0000002e e:66
C2R,V0x0000002f e:65
C3R,V0x0000002f e:66
C0R,V0x0000002e e:66
C1R,V0x0000002f e:65
C2R,V0x00000030 e:65
C3R,V0x00000030 e:65
1244M
1866M
C0R,V0x00000016 e:66
C1R,V0x00000016 e:66
C2R,V0x00000016 e:66
C0R,V0x00000017 e:66
C1R,V0x00000017 e:66
C2R,V0x00000017 e:66
iomcu_subsys_init
boot_c0 PROFILE 4
main: ******** Fastboot for Kirin *****************
main: ******** Build Date: Jun 2 2017, 17:34:24 **
main: ******** Fastboot start at 1591 ms **********
main: print soc_id computed in xloader phase, is below:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
led_alwayson: can’t get dtb operators
bbox: bbox_register_module_ops success.
bfm: : >>>>>enter bfm_init
bfm: : [disable_boot_fail_system] boot_fail_system state is 0
clock: PLL Stat
clock: PLL2 ctrl0=0x04909604,ctrl1=0x02000000
clock: PLL2 acpu en_stat:0x00000008, acpu gt_stat:0x00040000
clock: PLL2 final en_stat:0x00100000, final gt_stat:0x00020000
clock: PLL3 ctrl0=0x04904005,ctrl1=0x07000000
clock: PLL3 acpu en_stat:0x00000000, acpu gt_stat:0x00000000
clock: PLL3 final en_stat:0x00200000, final gt_stat:0x00040000
clock: clock init OK
ufs: ufs start on platform[36600110]ufs: ufs current mode: 0x00000011
ufs: ufs current gear: 0x00000003
ufs: ufs mphy reg 0x4A = 0x00000000
ufs: bUD0BaseOffset: 0x00000010, bUDConfigPLength: 0x00000010
ufs: UFS device manufacturerid = 0x000001ce
ufs: UFS device: S******
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000001, mntnStageCode is 27
bfm: : <<<<<exit set_boot_stage.
storage: emmc_ops invalid
storage: storage type is UFS
bfm: : bfm system is disabled!
storage: emmc_init: BL2_STAGE_EMMC_OK is 33554435!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000003, mntnStageCode is 29
bfm: : <<<<>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010001, mntnStageCode is 30
bfm: : <<<<<exit set_boot_stage.
ddr: current logic version is lpddr4 verison !!!
ddr: ddr size is 3072MB
bbox: register modid [0x81fff200]
bbox: register exception succeed.
bbox: register modid [0x81fff202]
bbox: register exception succeed.
bbox: register modid [0x81fff20b]
bbox: register exception succeed.
watchdog: Enable watchdog start
boardid: [BDID]boardid: 5301
gpio: hikey960_gpio_init: GPIO 46 202 206 ouput low, GPIO 219 pullup.
load_kernel: register_update_dt_ops for usb!
usb: [USBERR]random_serial: fastboot serial: 6771546083000000
secureboot: Enter secboot_init: set pll efuse flag!
secureboot: pll efuse flag has been succ set!bbox: register modid [0x81fff20a]
bbox: register exception succeed.
secureboot: SECBOOT_DEV_INFO_DADDR = 0x1d7fff00, SECBOOT_DEV_INFO_SIZE = 0x00000040!
dtimage: number of dtb = 1
dtimage: =========uncompress_dtb_addr=[0x16f00000],====vrl_addr=[0x1b0e64e0]====
dtimage: [device_tree_get_dtb_entry:215] Verify Not Exist
dtimage: fdt_init success!
dtimage: -----can not find hisilicon,fastboot node by compatible
dtimage: -----can not find hisilicon,fastboot node by compatible
load_kernel: register_update_dt_ops for led!
dtimage: -----can not find hisilicon,fastboot node by compatible
vibrator: vibrator_delay: hisilicon,fastboot motor-vib_type failed!
dtimage: -----can not find hisilicon,fastboot node by compatible
vibrator: vibrator_off: hisilicon,fastboot motor-vib_type failed!
reboot_reason: scsysstat_value is 0x00000008
pmu: can not find fastboot,hisi-pmic-mntn node1
pmu: pmu_property_read_u32 fastboot,hisi-pmic-mntn, hisilicon,data-width, failed
pmu: pmu_mntn_record_dts_parse failed!
reboot_reason: enter [check_hardware_reset]
reboot_reason: Could not find path /sysctrl_reason
reboot_reason: get_sysctrl_reason_data is error
ddr: reset dmc_rint_0:00000000
ddr: reset dmc_rint_1:00000000
ddr: reset dmc_rint_2:00000000
ddr: reset dmc_rint_3:00000000
ddr: new dmc_rint_0:00000000
ddr: new dmc_rint_1:00000000
ddr: new dmc_rint_2:00000000
ddr: new dmc_rint_3:00000000
bbox: save_tempbuffer_to_loop_area():727:storage_read fail[-1]
reboot_reason: reboot_reason is FB_S_KERNEL_IMG_ERR
reboot_reason: clear_reset_source in!
reboot_reason: tmp =0x0effcc70
dtimage: -----can not find fastboot,charger node by compatible
power: get_chargerIC_type: getU32byCompatible fastboot,charger, hw_charger_type failed!
dtimage: -----can not find fastboot,coul node by compatible
power: get_coul_type: get coul_type failed!
power: get coul_type failed!
power: hi6421v500 register coulometer ops fail!
dtimage: -----can not find huawei,hisi_bci_battery node by compatible
no_module: [hi6523_get_config_info]: can’t get battery board type
dtimage: -----can not find fastboot,charger node by compatible
no_module: get hi6523 i2c reg num fail!
dtimage: -----can not find fastboot,charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get ichrg_pre_limit fail
dtimage: -----can not find huawei,hi6523_charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get reg fail
dtimage: -----can not find fastboot,buckboost node by compatible
max77813: get_buckboost_type: getU32byCompatible fastboot,buckboost, hw_buckboost_type failed!
max77813: get dts buckboost type fail!
cpu_buck: pmu type3 not registered
cpu_buck: Bad cpu buck info:1
bbox: Could not find path /rdr
bbox: Could not find status property.
mntn: tele_mntn_stat_point_init: can not bbox_ops !
dtimage: -----can not find hisilicon,fastboot node by compatible
mntn: [tele_mntn_m3_wdt_config]: getU32byCompatible(hisilicon,fastboot, lpm3-board-type) error!
mntn: mntn init
mntndump: enable_reserved_ddr_dts: Could not find path /reserved-memory/mntndump
mntndump: mntn_dump_init failed
mntndump: get_mntn_dump_addr:mid[2] is not init
mntn: kernel dump is not available
mntn: reboot_type is 125
mntn:
no need to dump_mem…
mntn: enter [registe_pstore_ramoops_dump]
mntndump: get_mntn_dump_addr:mid[5] is not init
mntn: no mdump_pstore info
mntn: M3_RDR_SYS_CONTEXT_BASE_ADDR is null
uart_cfg: [MNTN]:Could not find node.
uart_cfg: set_default_uart_cfg: uart_from_dts_read failed!
uart_cfg: module_idx 2, uart_no 6
uart_cfg: odule_idx 11, uart_no 15
uart_cfg: module_idx 2, uart_no 6
uart_cfg: getU32byCompatible(hisilicon,fastboot, uart-board-type) error!
uart_cfg: boardid: 5301 use uart port: 6
pasr: in pasr_init-43 …ddr: current logic version is lpddr4 verison !!!
ddr: current logic version is lpddr4 verison !!!
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_detect_type: huawei,lcd_panel_type: get detect_type fail
display: lcd:no lcd detect_type
no_module: [LOGO] get_logo_buffer_from_dtsi: Could not find path /reserved-memory/logo-buffer.
no_module: [LOGO] logo_init: logo init failed!!! used the default fb addr.
display: [display]jdi_nt35696_panel_init: lcd type is not JDI_NT35696_5P5_LCD.
display: [display]jdi_otm2503b_panel_init: lcd type is not JDI_OTM2503B_5P5_LCD.
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010002, mntnStageCode is 31
bfm: : <<<<<exit set_boot_stage.
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_dts_value: can not get huawei,lcd_panel_type, bl_bus_id=4!
dtimage: -----can not find ti,lm36923 node by compatible
display: [display]get_dts_value: can not get ti,lm36923, support=0!
display: get lm36923_support failed!
Audio_codec: [audio]:Could not find “hisilicon,codec-controller” node.
load_teeos: can not find fb node fingerprint
load_teeos: failed to find fb node ese_config
display: [display]hisi_get_disp_info: hisifb_data is NULL pointer, return!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010003, mntnStageCode is 32
bfm: : <<<<<exit set_boot_stage.
misc: [get_misc_message] mmc_read failed
preboot: [fastboot]: check_unlock_misc_info, line:1273 :get misc message failed.
preboot: [fastboot]: check_powerkey_misc_info, line:1242 :!!!CAUTION!!!:get keypad_operator FAIL!
preboot: [fastboot]: check_volumekey_state, line:943 :!!!CAUTION!!!:get keypad_operator FAIL!
misc: [get_misc_message] mmc_read failed
preboot: [fastboot]: comm_read_misc_cmd, line:501 :get misc message failed.
watchdog: Disable watchdog start
bfm: : [disable_boot_fail_system] boot_fail_system state is 0
rescue: ^^^^^^^^^[rescue_init] ok !
usbloader: bootmode is 4
usb: [USBFINFO]USB RESET
usb: [USBFINFO]USB CONNDONE, highspeed
usb: [USBFINFO]USB RESET
usb: [USBFINFO]USB CONNDONE, highspeed
usbloader: usb: online (highspeed)
usb: [USBFINFO]usb enum done