Thanks.
but it will not boot into the install image… It gets to switch on a hdmi monitor but I never see the normal install dialog…
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
B - 1546 - PBL, Start
B - 3492 - bootable_media_detect_entry, Start
B - 207298 - bootable_media_detect_success, Start
B - 207302 - elf_loader_entry, Start
B - 209071 - auth_hash_seg_entry, Start
B - 209281 - auth_hash_seg_exit, Start
B - 236499 - elf_segs_hash_verify_entry, Start
B - 295374 - PBL, End
B - 305915 - SBL1, Start
B - 369782 - pm_device_init, Start
D - 14792 - pm_device_init, Delta
B - 385154 - boot_flash_init, Start
D - 30 - boot_flash_init, Delta
B - 389149 - boot_config_data_table_init, Start
D - 341996 - boot_config_data_table_init, Delta - (0 Bytes)
B - 735721 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B - 741943 - sbl1_ddr_set_params, Start
B - 745633 - cpr_init, Start
D - 0 - cpr_init, Delta
B - 751245 - Pre_DDR_clock_init, Start
D - 183 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 763720 - pm_driver_init, Start
D - 6832 - pm_driver_init, Delta
B - 779214 - clock_init, Start
D - 30 - clock_init, Delta
B - 789340 - Image Load, Start
D - 43798 - QSEE Image Loaded, Delta - (567100 Bytes)
B - 833138 - Image Load, Start
D - 427 - SEC Image Loaded, Delta - (2048 Bytes)
B - 840305 - sbl1_efs_handle_cookies, Start
D - 0 - sbl1_efs_handle_cookies, Delta
B - 848205 - Image Load, Start
D - 20862 - QHEE Image Loaded, Delta - (51952 Bytes)
B - 869097 - Image Load, Start
D - 17050 - RPM Image Loaded, Delta - (149492 Bytes)
B - 886177 - Image Load, Start
D - 22692 - APPSBL Image Loaded, Delta - (480308 Bytes)
B - 908869 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 914573 - SBL1, End
D - 611006 - SBL1, Delta
S - Flash Throughput, 61000 KB/s (1250900 Bytes, 20374 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk
[10] platform_init()
[10] target_init()
[20] initialising mmc_slot =2
[20] Error: Command timeout error
[20] Failure getting OCR response from MMC Card
[30] MMC card failed to respond, try for SD card
[90] Done initialization of the card
[100] pm8x41_get_is_cold_boot: cold boot
[510] Not able to search the panel:
[520] Display not enabled for 24 HW type
[520] Target panel init not found!
[520] pm8x41_get_is_cold_boot: cold boot
[530] partition misc doesn’t exist
[530] error in emmc_recovery_init
[530] Unable to locate /bootselect partition
[540] No ‘misc’ partition found
[540] Error reading MISC partition
[540] failed to get ffbm cookie[550] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[550] Loading boot image (17741824): start
[1390] Loading boot image (17741824): done
[1520] DTB Total entry: 15, DTB version: 2
[1520] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
[1530] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
[1530] cmdline: root=/dev/mmcblk1p8 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=74d40c34 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[1550] Updating device tree: start
[1680] Setting mac address in DT: 2:0:74:d4:c:34
[1680] Updating device tree: done
[1690] Error: Command timeout error
[1690] card sleep error: mmc_put_card_to_sleep
[1690] booting linux @ 0x80080000, ramdisk @ 0x82000000 (3714984), tags/device tree @ 0x81e00000
[1700] Jumping to kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.23-linaro-lt-qcom (buildslave@x86_64-09) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Oct 6 08:25:14 UTC 2016
[ 0.000000] Boot CPU: aarch64 Processor [410fd030]
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: OVERLAP DETECTED!
[ 0.000000] hypervisor_region@86400000 (0x0000000086400000–0x0000000086800000) overlaps with rmtfs@86700000 (0x0000000086700000–0x00000000867e0000)
[ 0.000000] Reserved memory: OVERLAP DETECTED!
[ 0.000000] modem_adsp_region@86800000 (0x0000000086800000–0x000000008b000000) overlaps with wcnss@89300000 (0x0000000089300000–0x0000000089900000)
[ 0.000000] cma: Reserved 64 MiB at 0x00000000bc000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc03bf41000 s25216 r8192 d32128 u65536
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM errata 826319, 827319, 824069
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 234108
[ 0.000000] Kernel command line: root=/dev/mmcblk1p8 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=74d40c34 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[ 0.000000] log_buf_len min size: 16384 bytes
[ 0.000000] log_buf_len: 32768 bytes
[ 0.000000] early log buf free: 14036(85%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] software IO TLB [mem 0xb6c00000-0xbac00000] (64MB) mapped at [ffffffc036c00000-ffffffc03abfffff]
[ 0.000000] Memory: 783492K/951296K available (8393K kernel code, 798K rwdata, 3696K rodata, 576K init, 275K bss, 102268K reserved, 65536K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc1000000 ( 16 MB actual)
[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
[ 0.000000] .init : 0xffffffc000c51000 - 0xffffffc000ce1000 ( 576 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000c50404 ( 12098 KB)
[ 0.000000] .data : 0xffffffc000cf7000 - 0xffffffc000dbea00 ( 799 KB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000004] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000431] Console: colour dummy device 80x25
[ 0.000450] Calibrating delay loop (skipped), value calculated using timer frequency… 38.40 BogoMIPS (lpj=76800)
[ 0.000460] pid_max: default: 32768 minimum: 301
[ 0.000532] Security Framework initialized
[ 0.000581] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000590] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.001159] Initializing cgroup subsys io
[ 0.001176] Initializing cgroup subsys memory
[ 0.001202] Initializing cgroup subsys devices
[ 0.001214] Initializing cgroup subsys freezer
[ 0.001224] Initializing cgroup subsys net_cls
[ 0.001237] Initializing cgroup subsys perf_event
[ 0.001247] Initializing cgroup subsys net_prio
[ 0.001261] Initializing cgroup subsys hugetlb
[ 0.001270] Initializing cgroup subsys pids
[ 0.001537] EFI services will not be available.
[ 0.001559] ASID allocator initialised with 65536 entries
[ 0.035943] Detected VIPT I-cache on CPU1
[ 0.035981] CPU1: Booted secondary processor [410fd030]
[ 0.047953] Detected VIPT I-cache on CPU2
[ 0.047982] CPU2: Booted secondary processor [410fd030]
[ 0.059977] Detected VIPT I-cache on CPU3
[ 0.060004] CPU3: Booted secondary processor [410fd030]
[ 0.060057] Brought up 4 CPUs
[ 0.060081] SMP: Total of 4 processors activated.
[ 0.060090] CPU: All CPU(s) started at EL1
[ 0.060114] alternatives: patching kernel code
[ 0.060732] devtmpfs: initialized
[ 0.080213] DMI not present or invalid.
[ 0.080513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.082807] pinctrl core: initialized pinctrl subsystem
[ 0.084552] NET: Registered protocol family 16
[ 0.096005] cpuidle: using governor ladder
[ 0.100107] cpuidle: using governor menu
[ 0.100425] vdso: 2 pages (1 code @ ffffffc000cfd000, 1 data @ ffffffc000cfc000)
[ 0.100459] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.101282] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.101473] Serial: AMBA PL011 UART driver
[ 0.115192] irq: no irq domain found for /hexagon-smp2p/slave-kernel !
[ 0.116013] irq: no irq domain found for /wcnss-smp2p/slave-kernel !
[ 0.119504] irq: no irq domain found for /soc/qcom,mdss_mdp@1a00000 !
[ 0.153378] msm_bus_fabric_init_driver
[ 0.153552] msm_bus_device 580000.ad-hoc-bus: Dev 1024
[ 0.153570] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.153581] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.153840] msm_bus_device 580000.ad-hoc-bus: Dev 0
[ 0.153855] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.153865] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.154015] msm_bus_device 580000.ad-hoc-bus: Dev 4096
[ 0.154031] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.154040] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.160598] msm_bus_init_clk: Valid node clk node 1024 ctx 0
[ 0.160607] msm_bus_init_clk: Valid node clk node 1024 ctx 1msm_bus_init_clk: Valid node clk node 0 ctx 0
[ 0.160698] msm_bus_init_clk: Valid node clk node 0 ctx 1msm_bus_init_clk: Valid node clk node 4096 ctx 0
[ 0.160788] msm_bus_init_clk: Valid node clk node 4096 ctx 1[ 0.254301] vgaarb: loaded
[ 0.258507] SCSI subsystem initialized
[ 0.288263] usbcore: registered new interface driver usbfs
[ 0.289259] usbcore: registered new interface driver hub
[ 0.290601] usbcore: registered new device driver usb
[ 0.293013] media: Linux media interface: v0.10
[ 0.293628] Linux video capture interface: v2.00
[ 0.297003] dmi: Firmware registration failed.
[ 0.299258] Advanced Linux Sound Architecture Driver Initialized.
[ 0.308187] Bluetooth: Core ver 2.21
[ 0.308792] NET: Registered protocol family 31
[ 0.308847] Bluetooth: HCI device and connection manager initialized
[ 0.309053] Bluetooth: HCI socket layer initialized
[ 0.309177] Bluetooth: L2CAP socket layer initialized
[ 0.309497] Bluetooth: SCO socket layer initialized
[ 0.322626] clocksource: Switched to clocksource arch_sys_counter
[ 0.418222] NET: Registered protocol family 2
[ 0.425341] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.426821] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.431418] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.434239] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.434507] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.437736] NET: Registered protocol family 1
[ 0.442613] RPC: Registered named UNIX socket transport module.
[ 0.442650] RPC: Registered udp transport module.
[ 0.442664] RPC: Registered tcp transport module.
[ 0.442679] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.445544] Unpacking initramfs…
[ 1.105886] Freeing initrd memory: 3624K (ffffffc002000000 - ffffffc00238a000)
[ 1.113488] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.118152] kvm [1]: HYP mode not available
[ 1.141576] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 1.145437] audit: initializing netlink subsys (disabled)
[ 1.146450] audit: type=2000 audit(1.139:1): initialized
[ 1.155156] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.259542] VFS: Disk quotas dquot_6.6.0
[ 1.261793] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.294042] NFS: Registering the id_resolver key type
[ 1.294974] Key type id_resolver registered
[ 1.295009] Key type id_legacy registered
[ 1.298249] fuse init (API version 7.23)
[ 1.305347] 9p: Installing v9fs 9p2000 file system support
[ 1.321813] io scheduler noop registered
[ 1.324751] io scheduler cfq registered (default)
[ 1.434202] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.457582] msm_serial 78af000.serial: msm_serial: detected port #1
[ 1.460863] msm_serial 78af000.serial: uartclk = 3686400
[ 1.461839] 78af000.serial: ttyMSM1 at MMIO 0x78af000 (irq = 137, base_baud = 230400) is a MSM
[ 1.466608] msm_serial 78b0000.serial: msm_serial: detected port #0
[ 1.467381] msm_serial 78b0000.serial: uartclk = 3686400
[ 1.467848] 78b0000.serial: ttyMSM0 at MMIO 0x78b0000 (irq = 138, base_baud = 230400) is a MSM
[ 1.468002] msm_serial: console setup on port #0
[ 2.410394] console [ttyMSM0] enabled
[ 2.418609] msm_serial: driver initialized
[ 2.424139] [drm] Initialized drm 1.1.0 20060810
[ 2.430539] l6: supplied by s4
[ 2.459333] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[ 2.461469] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[ 2.468141] l2: supplied by s3
[ 2.475884] msm_dsi_manager_register: failed to register mipi dsi host for DSI 0
[ 2.477481] msm 1a00000.qcom,mdss_mdp: failed to bind 1a98000.qcom,mdss_dsi (ops dsi_ops): -517
[ 2.489287] msm 1a00000.qcom,mdss_mdp: master bind failed: -517
[ 2.579137] loop: module loaded
[ 2.605043] spi_qup 78b7000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 2.618029] spi_qup 78b9000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 2.627317] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[ 2.715891] tun: Universal TUN/TAP device driver, 1.6
[ 2.716186] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.726769] sky2: driver version 1.30
[ 2.730874] usbcore: registered new interface driver asix
[ 2.731952] usbcore: registered new interface driver ax88179_178a
[ 2.735834] usbcore: registered new interface driver cdc_ether
[ 2.741893] usbcore: registered new interface driver dm9601
[ 2.747603] usbcore: registered new interface driver net1080
[ 2.753092] usbcore: registered new interface driver plusb
[ 2.758936] usbcore: registered new interface driver cdc_subset
[ 2.764295] usbcore: registered new interface driver zaurus
[ 2.770572] usbcore: registered new interface driver cdc_ncm
[ 2.794574] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.794945] ehci-pci: EHCI PCI platform driver
[ 2.800892] ehci-platform: EHCI generic platform driver
[ 2.806592] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[ 2.812599] msm_hsusb_host 78d9000.ehci: unable to find transceiver
[ 2.816358] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 2.821763] ohci-pci: OHCI PCI platform driver
[ 2.828469] ohci-platform: OHCI generic platform driver
[ 2.834363] usbcore: registered new interface driver cdc_acm
[ 2.837376] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.843969] usbcore: registered new interface driver usblp
[ 2.851429] usbcore: registered new interface driver cdc_wdm
[ 2.856963] usbcore: registered new interface driver uas
[ 2.863064] usbcore: registered new interface driver usb-storage
[ 2.868986] usbcore: registered new interface driver usbserial
[ 2.873988] usbcore: registered new interface driver usbserial_generic
[ 2.879661] usbserial: USB Serial support registered for generic
[ 2.899570] usb3503 usb2513: switched to HUB mode
[ 2.899665] usb3503 usb2513: usb3503_probe: probed in hub mode
[ 2.909371] usbip_core: USB/IP Core v1.0.0
[ 2.910262] usbcore: registered new device driver usbip-host
[ 2.913226] usbip_host: USB/IP Host Driver v1.0.0
[ 2.923913] mousedev: PS/2 mouse device common for all mice
[ 2.935934] input: pm8941_pwrkey as /devices/platform/soc/200f000.spmi/spmi-0/0-00/200f000.spmi:pm8916@0:pwrkey@800/input/input0
[ 2.946408] rtc-pm8xxx 200f000.spmi:pm8916@0:rtc@6000: rtc core: registered pm8xxx_rtc as rtc0
[ 2.949138] i2c /dev entries driver
[ 2.959912] i2c_qup 78b6000.i2c:
[ 2.959912] tx channel not available
[ 2.969937] i2c_qup 78b8000.i2c:
[ 2.969937] tx channel not available
[ 3.011787] i2c_qup 78ba000.i2c:
[ 3.011787] tx channel not available
[ 3.024174] qcom-camss 1b0ac00.camss: notifier->num_subdevs = 0
[ 3.032200] msm_cci_init_gpio_params:1371 gpio count 0
[ 3.045247] l3: supplied by s3
[ 3.049504] CPR closed loop is enabled
[ 3.052565] CPR is enabled!
[ 3.068024] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed
[ 3.069419] Bluetooth: HCI UART driver ver 2.3
[ 3.073708] Bluetooth: HCI UART protocol H4 registered
[ 3.078053] Bluetooth: HCI UART protocol BCSP registered
[ 3.083159] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 3.089567] usbcore: registered new interface driver btusb
[ 3.100583] cpu: dev_pm_opp_of_cpumask_add_table: couldn’t find opp table for cpu:0, -19
[ 3.121271] sdhci: Secure Digital Host Controller Interface driver
[ 3.121478] sdhci: Copyright(c) Pierre Ossman
[ 3.127450] Synopsys Designware Multimedia Card Interface Driver
[ 3.134795] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.182072] l5: supplied by s4
[ 3.268275] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 3.276554] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 3.415117] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using ADMA 64-bit
[ 3.463083] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.495180] usbcore: registered new interface driver usbhid
[ 3.495956] usbhid: USB HID core driver
[ 3.507781] mmc0: MAN_BKOPS_EN bit is not set
[ 3.551466] 4080000.hexagon supply cx not found, using dummy regulator
[ 3.562297] 4080000.hexagon supply mss not found, using dummy regulator
[ 3.564614] l7: supplied by s4
[ 3.583952] mmc0: new HS200 MMC card at address 0001
[ 3.591126] remoteproc0: 4080000.hexagon is available
[ 3.591330] remoteproc0: Note: remoteproc is still under development and considered experimental.
[ 3.596079] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn’t yet guaranteed.
[ 3.606877] remoteproc0: Direct firmware load for mba.mbn failed with error -2
[ 3.613790] mmcblk0: mmc0:0001 H8G1e 7.28 GiB
[ 3.619826] qcom-tz-pil soc:vidc_tzpil@0: no crash reason id
[ 3.625147] soc:vidc_tzpil@0 supply qcom,pll not found, using dummy regulator
[ 3.625640] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uV, skipping
[ 3.625656] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uA, skipping
[ 3.625713] qcom-tz-pil soc:vidc_tzpil@0: no wdog IRQ defined
[ 3.625737] qcom-tz-pil soc:vidc_tzpil@0: no fatal IRQ defined
[ 3.625750] qcom-tz-pil soc:vidc_tzpil@0: no ready IRQ defined
[ 3.625772] qcom-tz-pil soc:vidc_tzpil@0: no handover IRQ defined
[ 3.625787] qcom-tz-pil soc:vidc_tzpil@0: no stop-ack IRQ defined
[ 3.626395] qcom-tz-pil soc:vidc_tzpil@0: Found relocation area 8388608@0x000000008f800000
[ 3.627473] remoteproc1: soc:vidc_tzpil@0 is available
[ 3.627486] remoteproc1: Note: remoteproc is still under development and considered experimental.
[ 3.627513] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn’t yet guaranteed.
[ 3.628795] remoteproc1: Direct firmware load for venus.mdt failed with error -2
[ 3.628895] remoteproc1: failed to load soc:vidc_tzpil@0
[ 3.645850] mmcblk0boot0: mmc0:0001 H8G1e partition 1 4.00 MiB
[ 3.651734] a204000.wcnss supply vddcx not found, using dummy regulator
[ 3.662311] mmcblk0boot1: mmc0:0001 H8G1e partition 2 4.00 MiB
[ 3.666383] mmcblk0rpmb: mmc0:0001 H8G1e partition 3 4.00 MiB
[ 3.688463] remoteproc2: a204000.wcnss is available
[ 3.688495] remoteproc2: Note: remoteproc is still under development and considered experimental.
[ 3.688519] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn’t yet guaranteed.
[ 3.689650] remoteproc2: Direct firmware load for wcnss.mdt failed with error -2
[ 3.725682] Alternate GPT is invalid, using primary GPT.
[ 3.726452] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
[ 3.849788] coresight-tmc 825000.etf: TMC initialized
[ 3.968715] coresight-tmc 826000.etr: TMC initialized
[ 4.024059] coresight-tpiu 820000.tpiu: TPIU initialized
[ 4.090047] coresight-funnel 821000.funnel: FUNNEL initialized
[ 4.100709] coresight-funnel 841000.funnel: FUNNEL initialized
[ 4.138306] coresight-etm4x 85c000.etm: ETM 4.0 initialized
[ 4.181624] coresight-etm4x 85d000.etm: ETM 4.0 initialized
[ 4.223360] coresight-etm4x 85e000.etm: ETM 4.0 initialized
[ 4.242111] coresight-etm4x 85f000.etm: ETM 4.0 initialized
[ 4.263614] coresight-replicator-qcom 824000.replicator: REPLICATOR 1.0 initialized
[ 4.284027] usbcore: registered new interface driver snd-usb-audio
[ 4.322844] mmc1: Reset 0x1 never completed.
[ 4.323367] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[ 4.323566] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[ 4.323730] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[ 4.323897] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[ 4.351287] msm8916-wcd-codec 200f000.spmi:pm8916@1:codec@f000: PMIC REV: 1 CODEC Version: 1
[ 4.365116] qcom-apq8016-sbc 7702000.sound: adv7511 <-> Quatenary MI2S mapping ok
[ 4.369228] qcom-apq8016-sbc 7702000.sound: msm8916_wcd_i2s_rx1 <-> Primary MI2S mapping ok
[ 4.372817] qcom-apq8016-sbc 7702000.sound: msm8916_wcd_i2s_tx1 <-> Tertiary MI2S mapping ok
[ 4.469762] NET: Registered protocol family 10
[ 4.508102] sit: IPv6 over IPv4 tunneling driver
[ 4.524971] NET: Registered protocol family 17
[ 4.537170] Bluetooth: RFCOMM TTY layer initialized
[ 4.537756] Bluetooth: RFCOMM socket layer initialized
[ 4.544879] Bluetooth: RFCOMM ver 1.11
[ 4.546655] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.552543] Bluetooth: HIDP socket layer initialized
[ 4.560024] 9pnet: Installing 9P2000 support
[ 4.568346] Key type dns_resolver registered
[ 4.570073] NET: Registered protocol family 42
[ 4.617429] registered taskstats version 1
[ 4.654371] msm_iommu 1f00000.qcom,iommu: invalid resource
[ 4.660021] msm_iommu 1f00000.qcom,iommu: iface: 100000000, core: 800000000
[ 4.660362] msm_iommu 1f00000.qcom,iommu: device gfx_iommu (model: 500) mapped at ffffff8000b20000, with 2 ctx banks
[ 4.666625] msm_iommu 1f00000.qcom,iommu: iommu sec: pgtable size: 94208
[ 4.700489] genirq: Setting trigger mode 1 for irq 159 failed (gic_set_type+0x0/0x5c)
[ 4.705536] msm_iommu 1f00000.qcom,iommu: Request Global CFG IRQ 159 failed with ret=-22
[ 4.732033] msm_iommu_ctx 1f09000.qcom,iommu-ctx: context gfx3d_user using bank 1
[ 4.755343] msm_iommu_ctx 1f0a000.qcom,iommu-ctx: context gfx3d_priv using bank 2
[ 4.762771] msm_iommu 1e00000.qcom,iommu: iface: 100000000, core: 800000000
[ 4.764267] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8006400000, with 20 ctx banks
[ 4.781170] genirq: Setting trigger mode 1 for irq 159 failed (gic_set_type+0x0/0x5c)
[ 4.789594] msm_iommu 1e00000.qcom,iommu: Request Global CFG IRQ 159 failed with ret=-22
[ 4.803119] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context jpeg_enc0 using bank 2
[ 4.813714] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context vfe using bank 3
[ 4.831133] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context mdp_0 using bank 4
[ 4.842734] msm_iommu_ctx 1e25000.venus_ns: context venus_ns using bank 5
[ 4.849243] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context cpp using bank 6
[ 4.857884] msm_iommu_ctx 1e27000.qcom,iommu-ctx: context mDSP using bank 7
[ 4.865969] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context gss using bank 8
[ 4.878367] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context a2 using bank 9
[ 4.896336] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context mdp_1 using bank 18
[ 4.913517] msm_iommu_ctx 1e33000.venus_sec_pixel: context venus_sec_pixel using bank 19
[ 4.928557] msm_iommu_ctx 1e34000.venus_sec_bitstream: context venus_sec_bitstream using bank 20
[ 4.943184] msm_iommu_ctx 1e35000.venus_sec_non_pixel: context venus_sec_non_pixel using bank 21
[ 4.958329] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_fw using bank 22
[ 4.970372] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context periph_rpm using bank 23
[ 4.992686] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context periph_CE using bank 24
[ 5.004774] msm_iommu_ctx 1e39000.qcom,iommu-ctx: context periph_BLSP using bank 25
[ 5.021093] msm_iommu_ctx 1e3a000.qcom,iommu-ctx: context periph_SDC1 using bank 26
[ 5.037100] msm_iommu_ctx 1e3b000.qcom,iommu-ctx: context periph_SDC2 using bank 27
[ 5.052453] msm_iommu_ctx 1e3c000.qcom,iommu-ctx: context periph_audio using bank 28
[ 5.064266] msm_iommu_ctx 1e3d000.qcom,iommu-ctx: context periph_USB_HS1 using bank 29
[ 5.117541] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[ 5.120694] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[ 5.142251] msm 1a00000.qcom,mdss_mdp: bound 1a98000.qcom,mdss_dsi (ops dsi_ops)
[ 5.143903] msm 1a00000.qcom,mdss_mdp: bound 1c00000.qcom,adreno-3xx (ops a3xx_ops)
[ 5.151211] 1a00000.qcom,mdss_mdp supply vdd not found, using dummy regulator
[ 5.192469] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 5.192923] [drm] No driver support for vblank timestamp query.
[ 5.928451] Console: switching to colour frame buffer device 240x67
[ 5.978436] msm 1a00000.qcom,mdss_mdp: fb0: msm frame buffer device
[ 5.994274] [drm] Initialized msm 1.0.0 20130625 on minor 0
[ 5.995105] msm_otg 78d9000.phy: OTG regs = ffffff800061a000
[ 5.998956] msm_otg 78d9000.phy: no vddcx
[ 6.113516] msm_hsusb_host 78d9000.ehci: EHCI Host Controller
[ 6.113838] msm_hsusb_host 78d9000.ehci: new USB bus registered, assigned bus number 1
[ 6.119252] msm_hsusb_host 78d9000.ehci: irq 149, io mem 0x078d9000
[ 6.125322] input: gpio_keys as /devices/platform/gpio_keys/input/input1
[ 6.126053] rtc-pm8xxx 200f000.spmi:pm8916@0:rtc@6000: setting system clock to 1970-01-01 00:12:20 UTC (740)
[ 6.133181] ALSA device lis�[ 6.152867] Freeing unused kernel memory: 576K (ffffffc000c51000 - ffffffc000ce1000)
[ 6.152928] Freeing alternatives memory: 64K (ffffffc000ce1000 - ffffffc000cf1000)
[ 6.162299] msm_hsusb_host 78d9000.ehci: USB 2.0 started, EHCI 1.00
[ 6.167261] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.173231] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.180206] usb usb1: Product: EHCI Host Controller
[ 6.187290] usb usb1: Manufacturer: Linux 4.4.23-linaro-lt-qcom ehci_hcd
[ 6.189416] random: systemd-udevd: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.189788] random: systemd-udevd: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.189847] random: systemd-udevd: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.192979] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193135] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193186] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193274] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193578] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193662] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.193937] random: udevadm: uninitialized urandom read (16 bytes read, 22 bits of entropy available)
[ 6.283311] usb usb1: SerialNumber: 78d9000.ehci
[ 6.293393] hub 1-0:1.0: USB hub found
[ 6.297233] hub 1-0:1.0: 1 port detected
Loading, please wait…
starting version 230
[ 6.610167] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[ 6.742817] usb 1-1: New USB device found, idVendor=0424, idProduct=2513
[ 6.742849] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 6.749604] hub 1-1:1.0: USB hub found
[ 6.757077] hub 1-1:1.0: 2 ports detected
Begin: Loading essential drivers … done.
Begin: Running /scripts/init-premount … done.
Begin: Mounting root file system … Begin: Running /scripts/local-top … done.
Begin: Running /scripts/local-premount … done.
Begin: Waiting for root file system … [ 7.030203] usb 1-1.1: new full-speed USB device number 3 using msm_hsusb_host
[ 7.124717] usb 1-1.1: New USB device found, idVendor=e0ff, idProduct=0002
[ 7.124741] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.130505] usb 1-1.1: Product: G4
[ 7.137697] usb 1-1.1: Manufacturer: A…
[ 7.146189] input: A… G4 as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.1/1-1.1:1.0/0003:E0FF:0002.0001/input/input2
[ 7.147022] hid-generic 0003:E0FF:0002.0001: input: USB HID v1.00 Mouse [A… G4] on usb-78d9000.ehci-1.1/input0
[ 7.160317] input: A… G4 as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.1/1-1.1:1.1/0003:E0FF:0002.0002/input/input3
[ 7.222598] hid-generic 0003:E0FF:0002.0002: input: USB HID v1.00 Keyboard [A… G4] on usb-78d9000.ehci-1.1/input1
[ 7.298248] usb 1-1.2: new low-speed USB device number 4 using msm_hsusb_host
[ 7.412135] usb 1-1.2: New USB device found, idVendor=0c40, idProduct=8000
[ 7.412162] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.417919] usb 1-1.2: Product: iPazzPort
[ 7.425120] usb 1-1.2: Manufacturer: ELMCU
[ 7.434983] input: ELMCU iPazzPort as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.0/0003:0C40:8000.0003/input/input4
[ 7.491099] hid-generic 0003:0C40:8000.0003: input: USB HID v1.11 Keyboard [ELMCU iPazzPort] on usb-78d9000.ehci-1.2/input0
[ 7.496715] input: ELMCU iPazzPort as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.1/0003:0C40:8000.0004/input/input5
[ 7.555442] hid-generic 0003:0C40:8000.0004: input: USB HID v1.11 Mouse [ELMCU iPazzPort] on usb-78d9000.ehci-1.2/input1
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
[ 29.060216] random: nonblocking pool is initialized
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
Begin: Running /scripts/local-block … done.
done.
Gave up waiting for root device. Common problems: