Hey all, I made an attempt to install the newly released Fedora 31 (Workstation) on the Dragonboard, but have run into an issue. I began by following the steps located at Install Fedora on Dragonboard410c - 96Boards
I have downloaded installed the artifacts, as stated:
sudo ./flashall
sudo fastboot flash aboot emmc_appsboot.mbn
sudo fastboot flash boot u-boot.img
sudo fastboot oem select-display-panel adv7533_1080p
Then, on an x86 Fedora 31 host, I installed and ran arm-image-installer. Specifically, I ran:
sudo arm-image-installer --image=Fedora-Workstation-31.aarch64.raw.xz --addconsole --norootpass --resizefs --target=dragonboard410c --media=/dev/sdb
That completes successfully, I set Jumper S6 to SD Boot, insert the SD Card, and boot up.
Over Serial I can watch the boot begin, but then fail at random number generation:
`Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00286
S - IMAGE_VARIANT_STRING=HAAAANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
B - 1544 - PBL, Start
B - 3489 - bootable_media_detect_entry, Start
B - 251302 - bootable_media_detect_success, Start
B - 251306 - elf_loader_entry, Start
B - 253470 - auth_hash_seg_entry, Start
B - 253679 - auth_hash_seg_exit, Start
B - 269241 - elf_segs_hash_verify_entry, Start
B - 329472 - PBL, End
B - 274286 - SBL1, Start
B - 325465 - pm_device_init, Start
D - 14274 - pm_device_init, Delta
B - 340075 - boot_flash_init, Start
D - 0 - boot_flash_init, Delta
B - 344101 - boot_config_data_table_init, Start
D - 107482 - boot_config_data_table_init, Delta - (452 Bytes)
B - 456158 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B - 462380 - sbl1_ddr_set_params, Start
B - 466192 - cpr_init, Start
D - 0 - cpr_init, Delta
B - 471804 - Pre_DDR_clock_init, Start
D - 213 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 484401 - pm_driver_init, Start
D - 3477 - pm_driver_init, Delta
B - 496479 - SBC platform detected: XO_ADJ_FINE = 0x20
B - 496509 - clock_init, Start
D - 30 - clock_init, Delta
B - 511424 - Image Load, Start
D - 33153 - QSEE Image Loaded, Delta - (567468 Bytes)
B - 544608 - Image Load, Start
D - 366 - SEC Image Loaded, Delta - (2048 Bytes)
B - 551775 - sbl1_efs_handle_cookies, Start
D - 61 - sbl1_efs_handle_cookies, Delta
B - 559644 - Image Load, Start
D - 20100 - QHEE Image Loaded, Delta - (56048 Bytes)
B - 579774 - Image Load, Start
D - 14274 - RPM Image Loaded, Delta - (149316 Bytes)
B - 594048 - Image Load, Start
D - 14274 - APPSBL Image Loaded, Delta - (519792 Bytes)
B - 608322 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 614026 - SBL1, End
D - 342088 - SBL1, Delta
S - Flash Throughput, 118000 KB/s (1295124 Bytes, 10919 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] [0] BUILD_VERSION=
[0] [0] BUILD_DATE=15:11:10 - Oct 5 2017
[0] [0] welcome to lk
[10] [10] platform_init()
[10] [10] target_init()
[50] [50] SDHC Running in HS200 mode
[70] [70] Done initialization of the card
[80] [80] pm8x41_get_is_cold_boot: cold boot
[90] [90] Neither ‘config’ nor ‘frp’ partition found
[90] [90] Not able to search the panel:adv7533_1080p
[100] [100] Display not enabled for 24 HW type
[100] [100] Target panel init not found!
[100] [100] pm8x41_get_is_cold_boot: cold boot
[110] [110] partition misc doesn’t exist
[110] [110] error in emmc_recovery_init
[110] [110] Unable to locate /bootselect partition
[120] [120] No ‘misc’ partition found
[120] [120] Error reading MISC partition
[130] [130] failed to get ffbm cookie[130] [130] Loading boot image (468992): start
[140] [140] Loading boot image (468992): done
[140] [140] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[150] [150] DTB Total entry: 5, DTB version: 2
[150] [150] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
[160] [160] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
[170] [170] target_display_panel_node:510: hw_id=24 panel_name=" adv7533_1080p"
[180] [180] cmdline: androidboot.emmc=true androidboot.serialno=bf113c68 androidboot.baseband=apq adv7533_dsi2hdmi.panel=hdmi1080p mdss_mdp.panel=1:dsi:0:qcom,mdss_dsi_adv7533_1080p
[190] [190] Updating device tree: start
[200] [200] Updating device tree: done
[350] [350] booting linux @ 0x80080000, ramdisk @ 0x84000000 (0), tags/device tree @ 0x83e00000
[360] [360] Jumping to kernel via monitor
U-Boot 2017.11 (Nov 24 2017 - 12:02:00 +0000)
Qualcomm-DragonBoard 410C
DRAM: 986 MiB
MMC: sdhci@07864000: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
starting USB…
USB0: USB EHCI 1.00
scanning bus 0 for devices… 3 USB Device(s) found
scanning usb for storage devices… 0 Storage Device(s) found
Device 0: unknown device
MMC Device 1 not found
no mmc device at slot 1
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1…
Found EFI removable media binary efi/fedora/grubaa64.efi
Found DTB mmc 0:2 /dtb/qcom/apq8016-sbc.dtb
47757 bytes read in 198 ms (235.4 KiB/s)
Scanning disk sdhci@07864000.blk…
Found 1 disks
reading efi/fedora/grubaa64.efi
2476792 bytes read in 285 ms (8.3 MiB/s)
Starting EFI application at 81000000 …
error: …/…/grub-core/commands/increment.c:50:No such variable
“boot_indeterminate”.
Fedora (5.3.7-301.fc31.aarch64) 31 (Thirty One)
System setup
Use the ▲ and ▼ keys to change the selection.
Press 'e' to edit the selected item, or 'c' for a command prompt.
The selected entry will be started automatically in 0s.
EFI stub: Booting Linux Kernel...
EFI stub: EFI_RNG_PROTOCOL unavailable, no randomness supplied
EFI stub: Using DTB from configuration table
EFI stub: ERROR: Failed to install memreserve config table!
EFI stub: Exiting boot services and installing virtual address map…
usb_kbd_remove: warning, ret=-67
device_remove: Device ‘usb_kbd’ failed to remove, but children are gone
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd030]
[ 0.000000] Linux version 5.3.7-301.fc31.aarch64 (mockbuild@buildvm-aarch64-02.arm.fedoraproject.org) (gcc version 9.2.1 20190827 (Red Hat 9.2.1-1) (GCC)) #1 SMP Mon Oct 21 19:03:54 UTC 2019
[ 0.000000] Machine model: Qualcomm Technologies, Inc. APQ 8016 SBC
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: EFI v2.05 by Das U-boot
[ 0.000000] efi: SMBIOS=0xbc13b000
[ 0.000000] cma: Reserved 256 MiB at 0x00000000ac000000
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000bd9fffff]
[ 0.000000] NUMA: NODE_DATA [mem 0xbd797780-0xbd7a4fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000bd9fffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000085ffffff]
[ 0.000000] node 0: [mem 0x0000000089f00000-0x000000008e9fffff]
[ 0.000000] node 0: [mem 0x000000008eb00000-0x00000000bc138fff]
[ 0.000000] node 0: [mem 0x00000000bc139000-0x00000000bc141fff]
[ 0.000000] node 0: [mem 0x00000000bc142000-0x00000000bd9acfff]
[ 0.000000] node 0: [mem 0x00000000bd9ad000-0x00000000bd9aefff]
[ 0.000000] node 0: [mem 0x00000000bd9af000-0x00000000bd9fffff]
[ 0.000000] Zeroed struct page in unavailable ranges: 11 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bd9fffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] psci: OSI mode supported.
[ 0.000000] percpu: Embedded 30 pages/cpu s83288 r8192 d31400 u122880
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM errata 826319, 827319, 824069, 819472
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 232344
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=(hd0,msdos2)/vmlinuz-5.3.7-301.fc31.aarch64 root=UUID=78241bf0-43d1-4782-997a-770ea4f8f54b ro cma=256MB
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 562900K/944128K available (11516K kernel code, 2110K rwdata, 5296K rodata, 6272K init, 942K bss, 119084K reserved, 262144K cma-reserved)
[ 0.000000] random: get_random_u64 called from kmem_cache_open+0x38/0x258 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 42542 entries in 167 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000793] Console: colour dummy device 80x25
[ 0.001367] printk: console [tty0] enabled
[ 0.001488] Calibrating delay loop (skipped), value calculated using timer frequency… 38.40 BogoMIPS (lpj=192000)
[ 0.001517] pid_max: default: 32768 minimum: 301
[ 0.001693] LSM: Security Framework initializing
[ 0.001753] Yama: becoming mindful.
[ 0.001793] SELinux: Initializing.
[ 0.001916] *** VALIDATE SELinux ***
[ 0.001997] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002027] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002743] *** VALIDATE proc ***
[ 0.003033] *** VALIDATE cgroup1 ***
[ 0.003051] *** VALIDATE cgroup2 ***
[ 0.004131] ASID allocator initialised with 32768 entries
[ 0.004264] rcu: Hierarchical SRCU implementation.
[ 0.009168] Remapping and enabling EFI services.
[ 0.009715] smp: Bringing up secondary CPUs …
[ 0.010485] Detected VIPT I-cache on CPU1
[ 0.010539] CPU1: Booted secondary processor 0x0000000001 [0x410fd030]
[ 0.011390] Detected VIPT I-cache on CPU2
[ 0.011437] CPU2: Booted secondary processor 0x0000000002 [0x410fd030]
[ 0.012251] Detected VIPT I-cache on CPU3
[ 0.012292] CPU3: Booted secondary processor 0x0000000003 [0x410fd030]
[ 0.012401] smp: Brought up 1 node, 4 CPUs
[ 0.012477] SMP: Total of 4 processors activated.
[ 0.012492] CPU features: detected: 32-bit EL0 Support
[ 0.012507] CPU features: detected: CRC32 instructions
[ 0.016581] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.016605] CPU: All CPU(s) started at EL1
[ 0.016643] alternatives: patching kernel code
[ 0.018759] devtmpfs: initialized
[ 0.031281] Registered cp15_barrier emulation handler
[ 0.031314] Registered setend emulation handler
[ 0.031726] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.031762] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.043904] pinctrl core: initialized pinctrl subsystem
[ 0.045276] SMBIOS 3.0 present.
[ 0.045312] DMI: qualcomm dragonboard410c/dragonboard410c, BIOS 2017.11 11/24/2017
[ 0.046115] NET: Registered protocol family 16
[ 0.046603] audit: initializing netlink subsys (disabled)
[ 0.046809] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[ 0.048814] cpuidle: using governor menu
[ 0.049040] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.056072] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.056688] Serial: AMBA PL011 UART driver
[ 0.083579] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.083606] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.083623] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.083641] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.924620] cryptd: max_cpu_qlen set to 1000
[ 0.933597] alg: No test for lzo-rle (lzo-rle-generic)
[ 0.933869] alg: No test for lzo-rle (lzo-rle-scomp)
[ 0.934132] alg: No test for 842 (842-generic)
[ 0.934413] alg: No test for 842 (842-scomp)
[ 0.951475] fbcon: Taking over console
[ 0.951510] ACPI: Interpreter disabled.
[ 0.952385] vgaarb: loaded
[ 0.952937] SCSI subsystem initialized
[ 0.953356] usbcore: registered new interface driver usbfs
[ 0.953415] usbcore: registered new interface driver hub
[ 0.953516] usbcore: registered new device driver usb
[ 0.953804] pps_core: LinuxPPS API ver. 1 registered
[ 0.953820] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.953853] PTP clock support registered
[ 0.954102] EDAC MC: Ver: 3.0.0
[ 0.955870] Registered efivars operations
[ 0.956785] NetLabel: Initializing
[ 0.956801] NetLabel: domain hash size = 128
[ 0.956812] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.956887] NetLabel: unlabeled traffic allowed by default
[ 0.957530] clocksource: Switched to clocksource arch_sys_counter
[ 1.055702] VFS: Disk quotas dquot_6.6.0
[ 1.055801] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.055940] *** VALIDATE hugetlbfs ***
[ 1.056354] pnp: PnP ACPI: disabled
[ 1.064145] thermal_sys: Registered thermal governor ‘fair_share’
[ 1.064150] thermal_sys: Registered thermal governor ‘step_wise’
[ 1.064173] thermal_sys: Registered thermal governor ‘user_space’
[ 1.065287] NET: Registered protocol family 2
[ 1.065905] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.065954] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.066054] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 1.066217] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.066361] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.066411] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.066639] NET: Registered protocol family 1
[ 1.066675] NET: Registered protocol family 44
[ 1.066695] PCI: CLS 0 bytes, default 64
[ 1.066907] Trying to unpack rootfs image as initramfs…
[ 4.850403] Freeing initrd memory: 71444K
[ 4.851098] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 4.851431] kvm [1]: HYP mode not available
[ 5.110813] Initialise system trusted keyrings
[ 5.110879] Key type blacklist registered
[ 5.111100] workingset: timestamp_bits=37 max_order=18 bucket_order=0
[ 5.119026] zbud: loaded
[ 5.148774] NET: Registered protocol family 38
[ 5.148809] Key type asymmetric registered
[ 5.148824] Asymmetric key parser ‘x509’ registered
[ 5.148899] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 5.149111] io scheduler mq-deadline registered
[ 5.149129] io scheduler kyber registered
[ 5.149354] io scheduler bfq registered
[ 5.149663] atomic64_test: passed
[ 5.165008] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 5.174447] msm_serial 78af000.serial: msm_serial: detected port #1
[ 5.174501] msm_serial 78af000.serial: uartclk = 19200000
[ 5.174564] 78af000.serial: ttyMSM1 at MMIO 0x78af000 (irq = 9, base_baud = 1200000) is a MSM
[ 5.175096] msm_serial 78b0000.serial: msm_serial: detected port #0
[ 5.175145] msm_serial 78b0000.serial: uartclk = 7372800
[ 5.175198] 78b0000.serial: ttyMSM0 at MMIO 0x78b0000 (irq = 10, base_baud = 460800) is a MSM
[ 5.175228] msm_serial: console setup on port #0
[ 6.090608] printk: console [ttyMSM0] enabled
[ 6.095727] msm_serial: driver initialized
[ 6.101251] qcom-iommu 1ef0000.iommu: iommu sec: pgtable size: 94208
[ 6.111479] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 6.112300] libphy: Fixed MDIO Bus: probed
[ 6.116685] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 6.120241] ehci-pci: EHCI PCI platform driver
[ 6.126761] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 6.131328] usbcore: registered new interface driver usbserial_generic
[ 6.137327] usbserial: USB Serial support registered for generic
[ 6.143987] mousedev: PS/2 mouse device common for all mice
[ 6.152377] device-mapper: uevent: version 1.0.3
[ 6.155605] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 6.161662] ledtrig-cpu: registered to indicate activity on CPUs
[ 6.169109] EFI Variables Facility v0.08 2004-May-17
[ 6.174578] efivars: get_next_variable: status=8000000000000007
[ 6.179931] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.185354] usbcore: registered new interface driver usbhid
[ 6.190700] usbhid: USB HID core driver
[ 6.197280] drop_monitor: Initializing network drop monitor service
[ 6.200135] Initializing XFRM netlink socket
[ 6.206887] NET: Registered protocol family 10
[ 6.263127] Segment Routing with IPv6
[ 6.263262] mip6: Mobile IPv6
[ 6.265772] NET: Registered protocol family 17
[ 6.270966] registered taskstats version 1
[ 6.273098] Loading compiled-in X.509 certificates
[ 6.481037] Loaded X.509 cert ‘Fedora kernel signing key: 8d526677ef9b455c0789749a6b3f7d23ea4a0d36’
[ 6.481234] zswap: loaded using pool lzo/zbud
[ 6.516935] Key type big_key registered
[ 6.541951] Key type encrypted registered
[ 6.542022] ima: No TPM chip found, activating TPM-bypass!
[ 6.544976] ima: Allocated hash algorithm: sha256
[ 6.550386] No architecture policies found
[ 6.568048] hctosys: unable to op▒[ 6.579993] Freeing unused kernel memory: 6272K
[ 6.630240] Checked W+X mappings: passed, no W+X pages found
[ 6.630288] rodata_test: all tests were successful
[ 6.634972] Run /init as init process
[ 6.670337] systemd[1]: System time before build time, advancing clock.
[ 6.705129] efivars: get_next_variable: status=8000000000000007
[ 6.737782] systemd[1]: systemd v243-4.gitef67743.fc31 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 6.738807] systemd[1]: Detected architecture arm64.
[ 6.759975] systemd[1]: Running in initial RAM disk.
Welcome to Fedora 31 (Workstation Edition) dracut-049-27.git20181204.fc31.1 (Initramfs)!
[ 6.807776] systemd[1]: No hostname configured.
[ 6.807831] systemd[1]: Set hostname to .
[ 6.811271] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.816348] systemd[1]: Initializing machine ID from random generator.
[ 7.169875] systemd[1]: /usr/lib/systemd/system/iscsiuio.service:13: PIDFile= references a path below legacy directory /var/run/, updating /var/run/iscsiuio.pid → /run/iscsiuio.pid; please update the unit file accordingly.
[ 7.172363] systemd[1]: /usr/lib/systemd/system/iscsid.service:11: PIDFile= references a path below legacy directory /var/run/, updating /var/run/iscsid.pid → /run/iscsid.pid; please update the unit file accordingly.
[ 7.224142] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.224242] systemd[1]: Reached target Local File Systems.
[ OK ] Reached target Local File Systems.
[ 7.267873] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.267966] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ OK ] Reached target Swap.
[ OK ] Reached target Timers.
[ OK ] Listening on Journal Audit Socket.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Starting Create list of st…odes for the current kernel…
Starting Journal Service…
Starting Load Kernel Modules…
Starting Setup Virtual Console…
[ OK ] Started Create list of sta… nodes for the current kernel.[ 7.637708] fuse: init (API version 7.31)
[ OK ] Started Load Kernel Modules.
[ OK ] Started Setup Virtual Console.
Starting dracut cmdline hook…
Starting Apply Kernel Variables…
Starting Create Static Device Nodes in /dev…
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Create Static Device Nodes in /dev.
[ 8.286527] Loading iSCSI transport class v2.0-870.
[ 8.326743] iscsi: registered transport (tcp)
[ 8.419582] iscsi: registered transport (qla4xxx)
[ 8.419685] QLogic iSCSI HBA Driver
[ OK ] Started Journal Service.
[ 8.451563] libcxgbi:libcxgbi_init_module: Chelsio iSCSI driver library libcxgbi v0.9.1-ko (Apr. 2015)
[ 8.478467] audit: type=1130 audit(1570712162.799:2): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=systemd-journald comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
Starting Create Volatile Files and Directories…
[ 8.513569] Chelsio T3 iSCSI Driver cxgb3i v2.0.1-ko (Apr. 2015)
[ 8.513716] iscsi: registered transport (cxgb3i)
[ OK ] Started Create Volatile Files and Directories.
[ 8.553439] audit: type=1130 audit(1570712162.869:3): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=systemd-tmpfiles-setup comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
[ 8.639806] Chelsio T4-T6 iSCSI Driver cxgb4i v0.9.5-ko (Apr. 2015)
[ 8.639939] iscsi: registered transport (cxgb4i)
[ 8.644881] cxgb4i:cxgb4i_init_module: cxgb4i dcb enabled.
[ 8.679336] cnic: QLogic cnicDriver v2.5.22 (July 20, 2015)
[ 8.698476] QLogic NetXtreme II iSCSI Driver bnx2i v2.7.10.1 (Jul 16, 2014)
[ 8.698627] iscsi: registered transport (bnx2i)
[ 8.739452] iscsi: registered transport (be2iscsi)
[ 8.739493] In beiscsi_module_init, tt=(ptrval)
[ OK ] Started dracut cmdline hook.
[ 8.868301] audit: type=1130 audit(1570712163.189:4): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=dracut-cmdline comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
Starting dracut pre-udev hook…
[ 9.082329] RPC: Registered named UNIX socket transport module.
[ 9.082371] RPC: Registered udp transport module.
[ 9.087052] RPC: Registered tcp transport module.
[ 9.091982] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.167706] random: fast init done
[ OK ] Started dracut pre-udev hook.
[ 9.584733] audit: type=1130 audit(1570712163.899:5): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=dracut-pre-udev comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
Starting udev Kernel Device Manager…
[ OK ] Started udev Kernel Device Manager.
[ 10.502044] audit: type=1130 audit(1570712164.819:6): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=systemd-udevd comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
Starting dracut pre-trigger hook…
[ OK ] Started dracut pre-trigger hook.
[ 10.878194] audit: type=1130 audit(1570712165.199:7): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=dracut-pre-trigger comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
Starting udev Coldplug all Devices…
Mounting Kernel Configuration File System…
[ OK ] Started udev Coldplug all Devices.
[ OK 11.349857] audit: type=1130 audit(1570712165.669:8): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=systemd-udev-trigger comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
0m] Mounted Kernel Configuration File System.
[ 11.440834] alg: No test for stdrng (qcom-rng)
[ 11.497356] sdhci: Secure Digital Host Controller Interface driver
[ 11.497398] sdhci: Copyright(c) Pierre Ossman
[ 11.531648] sdhci-pltfm: SDHCI platform and OF driver helper
Starting dracut initqueue hook…
[ 11.562136] i2c_qup 78b6000.i2c: using default clock-frequency 100000
[ 11.562192] i2c_qup 78b6000.i2c:
[ 11.562192] tx channel not available
[ 11.571960] i2c_qup 78b8000.i2c: using default clock-frequency 100000
[ 11.574348] i2c_qup 78b8000.i2c:
[ 11.574348] tx channel not available
[ 11.588769] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 11.596878] i2c_qup 78ba000.i2c: using default clock-frequency 100000
[ 11.596933] i2c_qup 78ba000.i2c:
[ 11.596933] tx channel not available
[ 11.605058] sdhci_msm 7864900.sdhci: Got CD GPIO
Starting Show Plymouth Boot Screen…
[ 11.634419] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 11.658148] smd:rpm: failed to parse smd edge
[ 11.659492] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 11.675790] sdhci_msm 7864900.sdhci: Got CD GPIO
[ OK 11.680763] audit: type=1130 audit(1570712165.999:9): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=plymouth-start comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
m] Started Show Plymouth Boot Screen.
[ OK ] Started Forward Password R…s to Plymouth Directory Watch.
[ OK ] Reached target Local Encrypted Volumes.
[ OK ] Reached target Paths.
[ OK ] Reached target System Initialization.
[ OK ] Listening on Open-iSCSI iscsid Socket.
[ OK ] Listening on Open-iSCSI iscsiuio Socket.
[ 11.716796] audit: type=1130 audit(1570712166.029:10): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=iscsiuio comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
[ OK ] Reached target Basic System.
Starting iSCSI UserSpace I/O driver…
[ OK ] Started iSCSI UserSpace I/O driver[ 11.769927] usb3503 usb2513: usb3503_probe: probed in hub mode
.
Starting Open-iSCSI…[ 11.796054] audit: type=1130 audit(1570712166.109:11): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg=‘unit=iscsid comm=“systemd” exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success’
[ OK ] Started Open-iSCSI.
[ 11.882768] rtc-pm8xxx 200f000.spmi:pm8916@0:rtc@6000: registered as rtc0
[ 11.889176] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 11.900663] msm_hsusb 78d9000.usb: 78d9000.usb supply vbus not found, using dummy regulator
[ 11.931606] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 11.943155] adv7511 3-0039: failed to init regulators
[ 12.131963] adreno 1c00000.gpu: Adding to iommu group 0
[ 12.135765] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 12.137331] adv7511 3-0039: failed to init regulators
[ 12.142771] msm_mdp 1a01000.mdp: Adding to iommu group 1
[ 12.145984] msm_mdp 1a01000.mdp: No interconnect support may cause display underflows!
[ 12.153556] msm_dsi_phy 1a98300.dsi-phy: [drm:dsi_phy_driver_probe [msm]] ERROR dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 12.159194] msm_dsi_phy 1a98300.dsi-phy: [drm:dsi_phy_driver_probe [msm]] ERROR dsi_phy_driver_probe: failed to init regulator
[ 12.178149] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 12.188743] adv7511 3-0039: failed to init regulators
[ 12.190417] msm_dsi_phy 1a98300.dsi-phy: [drm:dsi_phy_driver_probe [msm]] ERROR dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 12.192968] msm_dsi_phy 1a98300.dsi-phy: [drm:dsi_phy_driver_probe [msm]] ERROR dsi_phy_driver_probe: failed to init regulator
[ 68.167699] random: crng init done
[ 68.167745] random: 7 urandom warning(s) missed due to ratelimiting
[ 200.308041] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 201.107164] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 201.912764] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 202.662442] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 203.453851] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 204.232417] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 204.983823] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 205.761810] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 206.556220] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 207.302428] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 208.092966] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 208.842135] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 209.613411] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 210.392285] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 211.144031] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 211.894119] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 212.644127] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 213.394378] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 214.144804] dracut-initqueue[495]: Warning: dracut-initqueue timeout - starting timeout scripts
`
Anyone able to duplicate this behavior? Or point out where I went wrong? Thanks!